FORD ECOBOOST CODE P04DB SOFTWARE
Integrated Diagnostic Software (IDS) / Ford Diagnosis & Repair System (FDRS)įor use with VCM I, VCM II, VMM and VCMM hardware devices only. Model Year Model Year Model Year Model Yearĭetailed system requirements, installation, and support information for each product is located under the diagnostics tool support tab for each product. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool.įor claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.ĭiagnostic Software Interface Device Complete Vehicle Diagnostics Module Programmingġ996-2017 2018-Present 1996-2017 2018-Present This may result in a no crank/no start/discharged battery condition. Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner’s Manual) built on 0 and through 0 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. SSM 47488 – 2018 Explorer/Police Interceptor Utility – No Crank/Discharged Battery/Battery Drain – Base Level IPC – Built On 0 And Through 0 THIS RE-LEARNING PROCESS MAY RESULT IN FIRMER THAN NORMAL UPSHIFTS AND DOWNSHIFTS FOR SEVERAL DAYS. WHEN THE ADAPTIVE STRATEGY IS RESET, THE COMPUTER WILL BEGIN A RE-LEARNING PROCESS. NOTE: ADVISE THE CUSTOMER THAT THIS VEHICLE IS EQUIPPED WITH AN ADAPTIVE TRANSMISSION SHIFT STRATEGY WHICH ALLOWS THE VEHICLE’S COMPUTER TO LEARN THE TRANSMISSION’S UNIQUE PARAMETERS AND IMPROVE SHIFT QUALITY. Warranty/ESP coverage limits are determined by the identified causal part and verified using the OASIS part coverage tool.Ģ017-2018 Explorer 2.3L: Retrieve DTCs And Reprogram The PCM (Do Not Use With Any Other Labor Operations) 182007A 0.3 Calibration files may also be obtained at Warranty Status: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage Warranty/ESP coverage limits/policies/prior approvals are not altered by a TSB. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Issue: Some 2017-2018 Explorer vehicles equipped with a 2.3L EcoBoost engine built on or before may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory.Īction: Reprogram the PCM using Integrated Diagnostic System (IDS) or Ford J2534 Diagnostic Software (FJDS) release 108.02 or higher. Maybe its a 2017 thing pertaining to the little sensor on the PCV.TSB 18-2007: 2.3L EcoBoost – Illuminated Malfunction Indicator Lamp (MIL) – Diagnostic Trouble Code (DTC) P04DB – Built On Or Before Personally, I get a lot of oil smell when the car blows off - I would assume we should be running a valve on the PCV instead of it just being open, but I was assuming mine was set up the same as others that do not have issues. The evap harness connects to the lower boost pipe, another tube with a check valve, and connects to the smaller nipple on the 2j intake. It didn't come with one and none was mentioned. My PCV goes from the existing right-angle PCV fitting (had to keep it in the loop due to a sensor not present on earlier cars), behind the engine cover along the firewall, then loops down to the 2j intake. I have the cobb evap fix thingy, not sure about OP. I'm a 2017, OP is a 2016, so we're both newer-style EVAP harnesses. When I get home I'll grab a few pics of how I have mine set up (since I am getting the same thing as OP).
FORD ECOBOOST CODE P04DB INSTALL
A lot of this would be a non-issue if they had even a basic install guide. I let them know that a few of us get it and asked if they could give us a definitive "normal or not". When I get a response I'll post back here. I just called 2j, left a message asking about the code and left my number for a call back. Click to expand.It doesn't create a CEL (at least for me), it simply creates a stored code p04db.
0 kommentar(er)
